Question
Offered Price $13.99

Introduction to Process Control Lab

Question # 00445780
Subject: Engineering
Due on: 12/20/2016
Posted On: 12/19/2016 09:47 AM

Rating:
4.1/5
Expert tutors with experiences and qualities
Posted By
Best Tutors for school students, college students
Questions:
769
Tutorials:
768
Feedback Score:

Purchase it
Report this Question as Inappropriate
Question

Introduction to Process Control Lab


1. You are taking a measurement of a signal from a sensor with high frequency noise. In order to not amplify that noise through your instrumentation system, you decide to use a RC filter with a cutoff frequency (critical frequency, fc) of 1kHz after the sensor and before the amplification.

2. What kind of RC filter do you need? Design the RC filter. Be sure to use standard resistor and capacitor values and specify the tolerance. Show all work.

3. Construct the circuit using Multisim. Use the tolerances which you specified in your design.

4. Use the multifunction generator for the input and use both channels of the Tektronix virtual scope to display the input and output voltages.

5. Create a table of your input and output voltage at dc, 250 Hz, 500Hz, 750Hz, 1kHz, 5kHz, 10kHz, 50kHz, 100kHz. Measure additional frequency points in order to get a nice set of data for the drop off. Be sure to capture several screenshots of the Tektronix virtual scope.

6. Given the output voltage at dc, what is the voltage 3dB down? In other words, what is the output voltage at the 3dB point? You should calculate this.

7. Using your simulation, change the frequency of the input voltage until the output voltage is that associated with your 3dB point. What is the frequency of the signal? That is your critical frequency. Take a screenshot of the scope. Add these measurements to your table. Also, put in your report this frequency. What is this frequency called?

8. Create a plot of your data (you can do this easily in Excel) and copy and paste the plot into your report.

9. Questions:

10. Does your circuit attenuate the signal at high frequencies? What is the attenuation at 10kHz?

11. How does your measured -3dB frequency (fc) compare to your design critical frequency? Give some reasons why it is different.

Please fill out and use the following.grantham.edu/at/uploads/Lab_report_template.docx">Lab Report Template when submitting your lab work.

1. You are taking a measurement of a signal from a sensor with high frequency noise. In order to not amplify that noise through your instrumentation system, you decide to use a RC filter with a cutoff frequency (critical frequency, fc) of 1kHz after the sensor and before the amplification.

1. What kind of RC filter do you need? Design the RC filter. Be sure to use standard resistor and capacitor values and specify the tolerance. Show all work.

2. Construct the circuit using Multisim. Use the tolerances which you specified in your design.

Use the multifunction generator for the input and use both channels of the Tektronix virtual scope to display the input and output voltages.

Create a table of your input and output voltage at dc, 250 Hz, 500Hz, 750Hz, 1kHz, 5kHz, 10kHz, 50kHz, 100kHz. Measure additional frequency points in order to get a nice set of data for the drop off. Be sure to capture several screenshots of the Tektronix virtual scope.

Given the output voltage at dc, what is the voltage 3dB down? In other words, what is the output voltage at the 3dB point? You should calculate this.

Using your simulation, change the frequency of the input voltage until the output voltage is that associated with your 3dB point. What is the frequency of the signal? That is your critical frequency. Take a screenshot of the scope. Add these measurements to your table. Also, put in your report this frequency. What is this frequency called?

Create a plot of your data (you can do this easily in Excel) and copy and paste the plot into your report.

Questions:

1. Does your circuit attenuate the signal at high frequencies? What is the attenuation at 10kHz?

2. How does your measured -3dB frequency (fc) compare to your design critical frequency? Give some reasons why it is different.

Please fill out and use the following.grantham.edu/at/uploads/Lab_report_template.docx">Lab Report Template when submitting your lab work.

Tags control proce introduction frequency voltage input output scope design critical signal sure using filter create 1khz point plot does report sensor noise high data table virtual order calculate change aociated screenshot need outputvoltage

Tutorials for this Question
Available for
$13.99

Introduction to Process Control Lab Tutorial Guide

Tutorial # 00441519
Posted On: 12/19/2016 09:48 AM
Posted By:
Best Tutors for school students, college students schoolbench
Expert tutors with experiences and qualities
Questions:
769
Tutorials:
768
Feedback Score:
Report this Tutorial as Inappropriate
Tutorial Preview …Please…
Attachments
Answer.zip (1964.19 KB)
Preview not available.
Purchase this Tutorial @ $13.99 *
* - Additional Paypal / Transaction Handling Fee (3.9% of Tutorial price + $0.30) applicable
Loading...