Attachment # 00010382 - Lab_1.1_Report_.docx
Lab_1.1_Report_.docx (1372.74 KB)
Raw Preview of Attachment:
(refer to the detailed question and attachment below)
Name:Date:Grade:Instructions: Complete Part 1, then Part 2 sections of the Lab 1.1. Then, complete this Lab Report by filling in all details. Use information you gained during your experimentation to complete the answers.Be sure to submit your lab report before the deadline.Part 1- Binary-to-Decimal Number Conversion Theory:Enter the decimal, hexadecimal, and BCD numbers for each of the following binary numbers.BinaryHexadecimalBCDDecimal0000000100100011010001010110011110001001101010111100110111101111Explain major differences between binary and BCD numeric representations.Planning:Provide a list of places that you can obtain the datasheets for the following components:SN74LS47 Binary to BCD DecoderMAN72 Seven Segment Display4116R 1-331 330 ohm Resistor PackPreparation:Why is it important to follow ESD safety procedures when handling electronic components? What are some of the main considerations?Wiring Procedure:Complete the wiring diagram. Refer to Lab 1.1 Figure 1-4 and image 1 & 2 of the ET1220.U1.Lab.Images PowerPoint. Use MS Paint to complete the wiring diagram.Test Procedure:Record the observed values from Lab 1.1 Table 1-1. Indicate which segments are illuminated for each input setting.InputsOutputBinaryData LinesBCD NumberSeven Segment Display321000000001001000110100010101100111100010011010Invalid1011Invalid1100Invalid1101Invalid1110Invalid1111InvalidTroubleshooting:For each trouble investigated, record your observations from Lab 1.1 Table 1-2. TroubleTroubleObservations1LED for the C segment is open. Break the connection to pin C of the 7-segment display (remove the wire).2An input to the 7447 is open. Break the connection to the input A pin of the 7447 (remove the wire).31000 ohm resistor is open. (Remove the 1kΩ resistor).Assume that the switches are set to a binary 1000 value, but the display shows a zero. What are three possible causes for this error?Part 2- Binary-Number Addition and Two’s Complement Subtraction Theory:Provide the results for the half-adder truth table.A0+B0S1S00+00+11+01+1Provide the results for the full-adder truth table.A0+B0+CinCoutS0+0+01+0+00+1+00+0+11+1+01+0+10+1+11+1+1Planning:Provide a list of places (links) where you can obtain the datasheets for the following components:74LS08 Quad AND Gate74LS32 Quad OR Gate74LC86 Quad XOR GatePreparation:What are several important things you should consider before wiring your circuit? Wiring Procedure:Complete the adder wiring diagram. Refer to Lab 1.1 Figure 1-12 and image 10 of the ET1220.U1.Lab.Images PowerPoint. Use MS Paint to complete the wiring diagram.Test Procedure:Record the observed values from Lab 1.1 Table 1-3. SwitchSwitch43Decimal Value of B21Decimal Value of AB1B0A1A0CalculatedSum7-SegmentDisplay00000000000011000102000113301100001101101110201111341020001020111021021021135113000113011113102113113
Tutorials for this Question
  1. Tutorial # 00446762 Posted By: schoolbench Posted on: 12/28/2016 02:57 AM
    Puchased By: 2
    Tutorial Preview
    The solution of ET1220: Module 1 Introduction to Digital Technology (Tutorial Guide)...
    Attachments
    Lab_1.1_Report_.docx (1438.31 KB)
Whatsapp Lisa